World Library  
Flag as Inappropriate
Email this Article

Rip saw

Article Id: WHEBN0001241989
Reproduction Date:

Title: Rip saw  
Author: World Heritage Encyclopedia
Language: English
Subject: Rip cut, Woodworking, Frame saw, Whipsaw, Crosscut saw
Collection: Saws, Woodworking Hand Tools
Publisher: World Heritage Encyclopedia
Publication
Date:
 

Rip saw

A rip saw

A rip saw is a wood saw that is specially designed for making a rip cut, a cut made parallel to the direction of the wood grain The cutting edge of each tooth has a flat front edge and it is angled backward by about 8°, in contrast to a crosscut saw, which has teeth angled backward by about 15°.[1] Another difference from the crosscut saw is that the edges are sharpened at right angles to the cutting plane, forming chisel-like cutting surfaces, whereas the crosscut saw is sharpened at an angle, so that each tooth has a knife-like cutting point in contact with the wood.[1] This design keeps the saw from following grain lines, which could curve the path of the saw: by acting like a chisel, the saw can more easily cut across deviating grain lines, which is necessary if a straight cut is to be achieved. This feature enables the orthogonal cutting edge to efficiently transport wood-chips from the kerf, allowing subsequent teeth to perform a more effective cut. It is possible to see this material removal mechanism in action by analyzing frame by frame footage of the cutting process.[2] Rip saws typically have 4-10 teeth per inch, making them relatively coarse.

All sawmills use rip saws of various types including the circular saw and band saw. Historically sawmills used one or more reciprocating saws more specifically known as an "up-and-down" or "upright saw" which are of two basic types, the frame saw or a muley (mulay) saw[3] which is similar to the hand powered pit saw. Some sawmills also use crosscut saws to cut boards and planks to length.

On the vast majority of saws throughout the world, the teeth are designed to cut when the saw is being pushed through the wood (on the push stroke or down stroke). However, some saws (such as Japanese saws and the saws used by Ancient Egyptians) are designed to cut on the pull stroke.

References

  1. ^ a b Lye, P.F. (1971). Woodwork theoryrip+saw" (Metric ed. ed.). London: Thomas Nelson. p. 23.  
  2. ^ Naylor, Andrew (May 2014). "Evaluating the Cutting Mechanics of Woodworking Hand-Saw Teeth" (PDF). IJMMM 2 (2). 
  3. ^ New international encyclopedia, 2nd ed. Volume 20. New York: Dodd, Mead, and Co. 1916. 601.

Further reading

  • Naylor, Andrew. Evaluating the Cutting Mechanics of Woodworking Hand-Saw Teeth. IJMMM, May 2014
This article was sourced from Creative Commons Attribution-ShareAlike License; additional terms may apply. World Heritage Encyclopedia content is assembled from numerous content providers, Open Access Publishing, and in compliance with The Fair Access to Science and Technology Research Act (FASTR), Wikimedia Foundation, Inc., Public Library of Science, The Encyclopedia of Life, Open Book Publishers (OBP), PubMed, U.S. National Library of Medicine, National Center for Biotechnology Information, U.S. National Library of Medicine, National Institutes of Health (NIH), U.S. Department of Health & Human Services, and USA.gov, which sources content from all federal, state, local, tribal, and territorial government publication portals (.gov, .mil, .edu). Funding for USA.gov and content contributors is made possible from the U.S. Congress, E-Government Act of 2002.
 
Crowd sourced content that is contributed to World Heritage Encyclopedia is peer reviewed and edited by our editorial staff to ensure quality scholarly research articles.
 
By using this site, you agree to the Terms of Use and Privacy Policy. World Heritage Encyclopedia™ is a registered trademark of the World Public Library Association, a non-profit organization.
 


Copyright © World Library Foundation. All rights reserved. eBooks from Project Gutenberg are sponsored by the World Library Foundation,
a 501c(4) Member's Support Non-Profit Organization, and is NOT affiliated with any governmental agency or department.