Reaction wheels

A reaction wheel (RW) is a type of flywheel used primarily by spacecraft for attitude control without using fuel for rockets or other reaction devices. They are particularly useful when the spacecraft must be rotated by very small amounts, such as keeping a telescope pointed at a star. They may also reduce the mass fraction needed for fuel. This is accomplished by equipping the spacecraft with an electric motor attached to a flywheel which, when its rotation speed is changed, causes the spacecraft to begin to counter-rotate proportionately through conservation of angular momentum. Reaction wheels can only rotate a spacecraft around its center of mass (see torque); they are not capable of moving the spacecraft from one place to another (see translational force). Reaction wheels work around a nominal zero rotation speed. However, external torques on the spacecraft may require a gradual buildup of reaction wheel rotation speed to maintain the spacecraft in a fixed orientation.

A reaction wheel is sometimes operated as (and referred to as) a momentum wheel, by operating it at a constant (or near-constant) rotation speed, in order to imbue a satellite with a large amount of stored angular momentum. Doing so alters the spacecraft's rotational dynamics so that disturbance torques perpendicular to one axis of the satellite (the axis parallel to the wheel's spin axis) do not result directly in spacecraft angular motion about the same axis as the disturbance torque; instead, they result in (generally smaller) angular motion (precession) of that spacecraft axis about a perpendicular axis. This has the effect of tending to stabilize that spacecraft axis to point in a nearly-fixed direction, allowing for a less-complicated attitude control system. Satellites using this "momentum-bias" stabilization approach include SCISAT-1; by orienting the momentum wheel's axis to be parallel to the orbit-normal vector, this satellite is in a "pitch momentum bias" configuration.

A control moment gyro (CMG) is a related but different type of attitude actuator, generally consisting of a momentum wheel mounted in a one-axis or two-axis gimbal. When mounted to a rigid spacecraft, applying a constant torque to the wheel using one of the gimbal motors causes the spacecraft to develop a constant angular velocity about a perpendicular axis, thus allowing control of the spacecraft's pointing direction. CMGs are generally able to produce larger sustained torques than RWs with less motor heating, and are preferentially used in larger and/or more-agile spacecraft, including Skylab and the International Space Station.


Reaction wheels are usually implemented as special electric motors, mounted along at least three directions: for example along the x, y and z axes provides no redundancy; while mounting four along tetrahedral axes provides redundancy.[1] Changes in speed (in either direction) are controlled electronically by computer. The strength of the materials of a reaction wheel determine the speed at which the wheel would come apart, and therefore how much angular momentum it can store.

Since the reaction wheel is a small fraction of the spacecraft's total mass, easily measurable changes in its speed provide very precise changes in angle. It therefore permits very precise changes in a spacecraft's attitude. For this reason, reaction wheels are often used to aim spacecraft with cameras or telescopes.

Over time reaction wheels may build up stored momentum that needs to be cancelled. Designers therefore supplement reaction wheel systems with other attitude control mechanisms. In the presence of a magnetic field (as in low Earth orbit), a spacecraft can employ magnetorquers (better known as torque rods) to transfer angular momentum to the Earth through its magnetic field. In the absence of a magnetic field, the most efficient practice is to use high-efficiency attitude jets such as ion thrusters, or small, lightweight solar sails on the ends of projecting masts or solar cell arrays. Most spacecraft, however, also need fast pointing, and cannot afford the extra mass of three attitude control systems. Designers therefore usually use conventional monopropellant vernier engines to cancel reaction wheels, as well as for fast pointing.


The failure of one or more reaction wheels can cause a spacecraft to lose its ability to maintain position and thus potentially cause a mission failure. In 2004, during the mission of the Hayabusa spacecraft, an X-axis reaction wheel failed. The Y-axis wheel failed in 2005 causing the craft to rely on chemical thrusters to maintain attitude control.[2]

By May 15, 2013, two reaction wheels in the Kepler telescope had failed. If the failures could not be corrected, Kepler would not be able to maintain a precise enough orientation to continue its original mission.[3] As of August 19, 2013, engineers concluded that Kepler's reaction wheels cannot be recovered. Although the failed reaction wheels still function, they are experiencing friction exceeding acceptable levels, and consequently hindering the ability of the telescope to properly orient itself. The Kepler telescope has been returned to its "point rest state", a stable configuration which uses small amounts of thruster fuel to compensate for the failed reaction wheels. Kepler's team is considering alternative uses for Kepler that do not require the extreme accuracy in its orientation as needed by the original mission.[4]

See also


External links

  • ca:Roda de reacció
This article was sourced from Creative Commons Attribution-ShareAlike License; additional terms may apply. World Heritage Encyclopedia content is assembled from numerous content providers, Open Access Publishing, and in compliance with The Fair Access to Science and Technology Research Act (FASTR), Wikimedia Foundation, Inc., Public Library of Science, The Encyclopedia of Life, Open Book Publishers (OBP), PubMed, U.S. National Library of Medicine, National Center for Biotechnology Information, U.S. National Library of Medicine, National Institutes of Health (NIH), U.S. Department of Health & Human Services, and, which sources content from all federal, state, local, tribal, and territorial government publication portals (.gov, .mil, .edu). Funding for and content contributors is made possible from the U.S. Congress, E-Government Act of 2002.
Crowd sourced content that is contributed to World Heritage Encyclopedia is peer reviewed and edited by our editorial staff to ensure quality scholarly research articles.
By using this site, you agree to the Terms of Use and Privacy Policy. World Heritage Encyclopedia™ is a registered trademark of the World Public Library Association, a non-profit organization.