World Library  
Flag as Inappropriate
Email this Article


Article Id: WHEBN0001295963
Reproduction Date:

Title: Empennage  
Author: World Heritage Encyclopedia
Language: English
Subject: Aircraft, Aeroflot accidents and incidents in the 1980s, Aft pressure bulkhead, IIL IS-12, Strake (aeronautics)
Collection: Aircraft Components
Publisher: World Heritage Encyclopedia


The empennage of a Boeing 747-200

The empennage ( or ),[1][2] also known as the tail or tail assembly, of most aircraft[1][2] gives stability to the aircraft, in a similar way to the feathers on an arrow;[3] the term derives from the French for this.[4] Most aircraft feature an empennage incorporating vertical and horizontal stabilising surfaces which stabilise the flight dynamics of yaw and pitch,[1][2] as well as housing control surfaces.

In spite of effective control surfaces, many early aircraft that lacked a stabilising empennage were virtually unflyable. Even so-called "tailless aircraft" usually have a tail fin (vertical stabiliser). Heavier than air aircraft without any kind of empennage (such as the McDonnell Douglas X-36) are rare.


  • Structure 1
  • Trim 2
  • Tail configurations 3
    • Tailplanes 3.1
    • Fins 3.2
    • V and X tails 3.3
    • Box kite tails 3.4
    • Tailless 3.5
  • See also 4
  • References 5


Structurally, the empennage consists of the entire tail assembly, including the tailfin, the tailplane and the part of the fuselage to which these are attached.[1][2] On an airliner this would be all the flying and control surfaces behind the rear pressure bulkhead.

The front (usually fixed) section of the tailplane is called the tailplane or horizontal stabiliser and is used to provide pitch stability. The rear section is called the elevator, and is usually hinged to the horizontal stabiliser. The elevator is a movable aerofoil that controls changes in pitch, the up-and-down motion of the aircraft's nose. Some aircraft employ an all-moving stabiliser and elevators in one unit, known as a stabilator or "full-flying stabiliser".[1][2]

The vertical tail structure (or fin) has a fixed front section called the vertical stabiliser, used to restrict side-to-side motion of the aircraft (yawing). The rear section of the vertical fin is the rudder, a movable aerofoil that is used to turn the aircraft's nose to one side or the other. When used in combination with the ailerons, the result is a banking turn, often referred to as a "coordinated turn".[1][2]

Some aircraft are fitted with a tail assembly that is hinged to pivot in two axes forward of the fin and stabiliser, in an arrangement referred to as a movable tail. The entire empennage is rotated vertically to actuate the horizontal stabiliser, and sideways to actuate the fin.[5]

The aircraft's cockpit voice recorder, flight data recorder and emergency locator transmitter (ELT) are often located in the empennage, because the aft of the aircraft provides better protection for these in most aircraft crashes.


In some aircraft trim devices are provided to eliminate the need for the pilot to maintain constant pressure on the elevator or rudder controls.[5][6]

The trim device may be:

  • a trim tab on the rear of the elevators or rudder which act to change the aerodynamic load on the surface. Usually controlled by a cockpit wheel or crank.[5][7]
  • an adjustable stabiliser into which the stabiliser may be hinged at its spar and adjustably jacked a few degrees in incidence either up or down. Usually controlled by a cockpit crank.[5][8]
  • a bungee trim system which uses a spring to provide an adjustable preload in the controls. Usually controlled by a cockpit lever.[5][6]
  • an anti-servo tab used to trim some elevators and stabilators as well as increased control force feel. Usually controlled by a cockpit wheel or crank.[5]
  • a servo tab used to move the main control surface, as well as act as a trim tab. Usually controlled by a cockpit wheel or crank.[5]

Multi-engined aircraft often have trim tabs on the rudder to reduce the pilot effort required to keep the aircraft straight in situations of asymmetrical thrust, such as single engine operations.[7]

Tail configurations

Aircraft empennage designs may be classified broadly according to the fin and tailplane configurations.

The overall shapes of individual tail surfaces (tailplane planforms, fin profiles) are similar to wing planforms.


The tailplane comprises the tail-mounted fixed horizontal stabiliser and movable elevator. Besides its planform, it is characterised by:

Some locations have been given special names:

  • Cruciform tail - The horizontal stabilisers are placed midway up the vertical stabiliser, giving the appearance of a cross when viewed from the front. Cruciform tails are often used to keep the horizontal stabilisers out of the engine wake, while avoiding many of the disadvantages of a T-tail. Examples include the Hawker Sea Hawk and Douglas A-4 Skyhawk.
  • T-tail - The horizontal stabiliser is mounted on top of the fin, creating a "T" shape when viewed from the front. T-tails keep the stabilisers out of the engine wake, and give better pitch control. T-tails have a good glide ratio, and are more efficient on low speed aircraft. However, T-tails are more likely to enter a deep stall, and are more difficult to recover from a spin. T-tails must be stronger, and therefore heavier than conventional tails. T-tails also have a larger radar cross section. Examples include the Gloster Javelin, Boeing 727 and McDonnell Douglas DC-9.

Fuselage mounted



Flying tailplane


The fin comprises the fixed vertical stabiliser and rudder. Besides its profile, it is characterised by:

  • Number of fins - usually one or two.
  • Location of fins - on the fuselage (over or under), tailplane, tail booms or wings

Twin fins may be mounted at various points:

Tailplane mounted

Twin tail boom

Wing mounted

Unusual fin configurations include:

Triple fins

Ventral fin

V and X tails

An alternative to the fin-and-tailplane approach is provided by the V-tail and X-tail designs. Here, the tail surfaces are set at diagonal angles, with each surface contributing to both pitch and yaw. The control surfaces, sometimes called ruddervators, act differentially to provide yaw control (in place of the rudder) and act together to provide pitch control (in place of the elevator).[1]

  • X tail: The Lockheed XFV and Convair XFY Pogo both featured "X" tails, which were reinforced and fitted with a wheel on each surface so that the craft could sit on its tail and take off and land vertically.
  • Pelikan: The Pelikan tail is an all-flying variation on the V tail. It was proposed for the Boeing X-32 but abandoned, and has not yet been used on any aircraft. The design is claimed to have the advantages of greater pitch control and a smaller radar signature.


Inverted V-tail


Pelikan tail

Box kite tails

Some of the earliest aircraft combined horizontal and vertical stabilisers in a box kite design, such as the 1910 Bristol Boxkite.


A tailless aircraft (often tail-less) traditionally has all its horizontal control surfaces on its main wing surface. It has no horizontal stabiliser - either tailplane or canard foreplane (nor does it have a second wing in tandem arrangement). A 'tailless' type usually still has a vertical stabilising fin (vertical stabiliser) and control surface (rudder). However, NASA adopted the 'tailless' description for the novel X-36 research aircraft which has a canard foreplane but no vertical fin.

The most successful tailless configuration has been the tailless delta, especially for combat aircraft.

See also


  1. ^ a b c d e f g Crane, Dale: Dictionary of Aeronautical Terms, third edition, page 194. Aviation Supplies & Academics, 1997. ISBN 1-56027-287-2
  2. ^ a b c d e f Aviation Publishers Co. Limited, From the Ground Up, page 10 (27th revised edition) ISBN 0-9690054-9-0
  3. ^
  4. ^
  5. ^ a b c d e f g Aviation Publishers Co. Limited, From the Ground Up, page 14 (27th revised edition) ISBN 0-9690054-9-0
  6. ^ a b Reichmann, Helmet: Flying Sailplanes, page 26. Thompson Publications, 1980.
  7. ^ a b Transport Canada: Flight Training Manual 4th Edition, page 12. Gage Educational Publishing Company, 1994. ISBN 0-7715-5115-0
  8. ^ Crane, Dale: Dictionary of Aeronautical Terms, third edition, page 524. Aviation Supplies & Academics, 1997. ISBN 1-56027-287-2
  9. ^ Anderson, John D., Introduction to Flight, 5th ed, p 517
This article was sourced from Creative Commons Attribution-ShareAlike License; additional terms may apply. World Heritage Encyclopedia content is assembled from numerous content providers, Open Access Publishing, and in compliance with The Fair Access to Science and Technology Research Act (FASTR), Wikimedia Foundation, Inc., Public Library of Science, The Encyclopedia of Life, Open Book Publishers (OBP), PubMed, U.S. National Library of Medicine, National Center for Biotechnology Information, U.S. National Library of Medicine, National Institutes of Health (NIH), U.S. Department of Health & Human Services, and, which sources content from all federal, state, local, tribal, and territorial government publication portals (.gov, .mil, .edu). Funding for and content contributors is made possible from the U.S. Congress, E-Government Act of 2002.
Crowd sourced content that is contributed to World Heritage Encyclopedia is peer reviewed and edited by our editorial staff to ensure quality scholarly research articles.
By using this site, you agree to the Terms of Use and Privacy Policy. World Heritage Encyclopedia™ is a registered trademark of the World Public Library Association, a non-profit organization.

Copyright © World Library Foundation. All rights reserved. eBooks from Project Gutenberg are sponsored by the World Library Foundation,
a 501c(4) Member's Support Non-Profit Organization, and is NOT affiliated with any governmental agency or department.